Rr400 - Holder (rod racks) for three spinings with the kit for installation on inflatables (Rr4000-1 + FMp224 x 2)
Technical Details:
Is designed to hold three spinning rods. Consists of two rod-racks and a pair of FMp224 mounting systems. The design of each rack comprises a Ø 20 mm tube of 430 mm length, and three pairs of brackets with elastic clamps. The tube is connected with an adapter, which is fixed in the mount of the FMp224 system, by a tilt joint with 15° splines. To fix a tilt position a square knob nut is included. Pads of FMp224 are 110 x 110 mm each. The kit assembly includes six M6*25 DIN 963 screws, two M6*30 DIN 933 bolts, DIN 912 (M4*20 — 6 pcs., M6*20 — 14 pcs., M6*45 — 2 pcs.) screws, six M4 DIN 985 nuts, eight M6 DIN 985 nuts, sixteen M6 DIN 934 nuts, twelve M6 DIN 125 washers. Tubes are made of anodized aluminium with powder coating, plastic parts — of fiberglass-reinforced polyamide, pads are covered with PVC, brackets and clamps — of polyurethane. Fasteners — of A2 (AISI 304) stainless steel (except for two M6 DIN 934 brass nuts).
| Category: | Borika Fasten |
|---|
Product description:
- This kit is designed especially for belly boats (float tubes), but it also suits for using on any PVC inflatable boat. It includes two rod racks and two FMp224 mounting systems intended to be glued outside the board, which is very important for saving space inside the vessel.
- The rod racks are designed for fixing 3 (three) spinning rods parallel to the board, as well as adjusting their tilt position in relation to the water surface. The system is perfect for ultralight fishing rods with a small handle.
- Polyurethane brackets, in which rods are placed, help to protect the handles from mechanical damage. Elastic clamps are easily adjustable in width and securely fix spinning rods, protecting them from loss. If necessary, both racks can be fixed in the raised position.
- All the aluminium tubes of the racks are anodized and covered with powder coating which ensures additional protection against rusting.
- The mounting systems are designed for medium loads, each of PVC pads is reinforced with a polyamide washer, fastened together with Fs219 accessory mount by four attachment points.
- Fixation in the mount is fast and simple: switch the locking mechanism into the UNLOCK position, insert an adapter all the way into the mount, and move the retainer into the LOCK position. You can rotate accessories in 30° increments.
Materials: fiberglass-reinforced polyamide, PVC, polyurethane, anodized aluminium with powder coating, A2 (AISI 304) stainless steel, brass.
In the package: an Rr400-1 set, two FMp224 mounting systems, and a step-by-step installation guide.
Tips on using & installation:
- The mounting kit is securely glued to the surface of the PVC cylinder with two-component polyurethane adhesive according to the step-by-step instructions and can be used for its intended purpose the day after installation.
- The recommended distance between the centers of the mounts is a multiple of 305 mm (305 mm, 610 mm, etc.), that allows accessories with paired adapters (trolling stands, round rails, tables) be fixed in the installed systems.
- The spinning rod racks can be removed, and in their place in the mounting systems from this kit, you can fix various accessories (fish finder plates and transducer arm mounts, action camera monopods, navigation lights, rigging, awnings, trolling stands) of both BORIKA FASTen® and other manufacturers ( SCOTTY®, RAM®, RAILBLAZA®, YakAttack®, carp fishing tackles, etc.), provided that adapters are used.
- To prolong the service life of the product, after using it in sea water, rinse it with plenty of fresh water.
